炼油技术与工程 ›› 2021, Vol. 51 ›› Issue (3): 48-52.

• 机械设备 • 上一篇    下一篇

固定床反应器内构件-喷射型分配器的结构优化*

薄守石, 雷瑞星, 杨昊, 张旭, 孙兰义**   

  1. 中国石油大学(华东)重质油国家重点实验室,山东省青岛市 266580
  • 收稿日期:2020-11-09 修回日期:2021-01-19 出版日期:2021-03-15 发布日期:2021-07-16
  • 通讯作者: ** 孙兰义,博士,2001年毕业于清华大学,现任中国石油大学(华东)化学工程学院教授。E-mail:sunlanyi@163.com。
  • 作者简介::薄守石,博士,2011年毕业于大连理工大学,现任中国石油大学(华东)化学工程学院讲师。E-mail:shoushibo@upc.edu.cn。
  • 基金资助:
    * 国家重点研发计划项目(2018YFB06044800)。

Structure optimization of spray distributor in fixed bed reactor

Bo Shoushi, Lei Ruixing, Yang Hao, Zhang Xu, Sun Lanyi   

  1. State Key Laboratory of Heavy Oil Processing, China University of Petroleum (East China), Qingdao, Shandong 266580
  • Received:2020-11-09 Revised:2021-01-19 Online:2021-03-15 Published:2021-07-16

PDF

摘要： 采用欧拉两相流模型和标准的k-ε湍流模型,对一种喷射型分配器进行了数值模拟,在此基础上探讨了气相入口结构、液相入口数量、出口喷嘴直径等对分配器不均匀度和压力降等性能的影响,进而优化了分配器结构。研究结果表明,改进型分配器气相入口形式为朝向同侧的2孔,液相入口个数为4个,出口喷嘴直径为12 mm,分配器下方200 mm的液相分布不均匀度为0.170 2,与基本构型分配器相比降低了3.46%,可在一定程度上改善分布效果;压力降与基本构型分配器的压力降相近。

关键词: 加氢反应器, 喷射型分配器, 结构优化, 液体分布不均匀度, 压力降

Abstract: The numerical simulation and optimization of a spray distributor are studied, and the mathematical model of the spray distributor is established by using the Euler two-phase flow model and the standard turbulence model. Based on the simulation analysis of the basic configuration of the spray distributor, the influences of the inlet structure of gas phase, the number of liquid phase inlets and the diameter of outlet nozzle on the nonuniformity and pressure drop of the distributor are discussed, and then the structure of the distributor is optimized. The results show that the gas phase inlet form of the modified distributor is 2 holes toward the same side, the number of liquid phase inlets is 4, and the outlet nozzle diameter is 12 mm. Its liquid distribution nonuniformity of catalyst bed layer is 0.170 2, which is reduced by 3.46% compared with basic configuration distributor, and it can achieve a good liquid distribution effect. The pressure drop is similar to that of the basic configuration distributor.

Key words: hydrogenation reactor, spray distributor, structure optimization, liquid distribution nonuniformity, pressure drop